knowledge of professional and technical personnel Notice on the organization of advanced research class on high-pressure science and new materials of engineering
Volume 35 Issue 2
Mar 2021
Turn off MathJax
Article Contents
Chinese Journal of High Pressure Physics  > 2021  >  35(2): 021101.
WANG Juwei, ZHANG Zhengang, LIANG Hao, CHEN Haihua. Effects of Sintering Pressure on the Vickers Hardness of TaC[J]. Chinese Journal of High Pressure Physics, 2021, 35(2): 021101. doi: 10.11858/gywlxb.20200600
Citation: WANG Juwei, ZHANG Zhengang, LIANG Hao, CHEN Haihua. Effects of Sintering Pressure on the Vickers Hardness of TaC[J]. Chinese Journal of High Pressure Physics, 2021, 35(2): 021101. doi: 10.11858/gywlxb.20200600
shu

Effects of Sintering Pressure on the Vickers Hardness of TaC

doi: 10.11858/gywlxb.20200600
  • 1.

    Department of Basic Education, Qinghai University, Xining 810016, Qinghai, China

  • 2.

    Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065, Sichuan, China

  • Received Date: 03 Aug 2020
  • Rev Recd Date: 26 Aug 2020
    Abstract
  • To study the effects of the sintering pressure on the mechanical properties of TaC with various grain sizes, nano- and micro-sized TaC powders are sintered at high pressure and high temperature (HPHT) to acquire bulk TaC ceramics under different sintering conditions. Different characterization approaches, such as X-ray diffraction (XRD), are used to observe phase, elements distribution, and indentation state. The observations reveal that the TaC phase is stable during the sintering process and there is no impurity infiltration. Three ceramic samples at the various sintering pressures (3.0, 4.0, 5.5 GPa) are measured by the Vickers hardness tester and their microstructures are also analyzed. The results show that as the sintering pressure increases from 3.0 GPa to 5.5 GPa, the Vickers hardness of Micro-5.5-TaC (21.0 GPa) is higher than that of Nano-3.0-TaC (17.5 GPa) and Nano-4.0-TaC (19.2 GPa). In addition, it is found that 3.0 kg is the most accurate load for measuring the Vickers hardness. This study has a guiding significance for sintering structural ceramics and exploring the Vickers hardness of ultra-high temperature ceramics (UHTCs).

     

    • FullText(HTML)
  • loading
    • References(22)
  • [1]
    CHENG Q, TANG S, LIU C, et al. Preparation and electrochemical performance of Li4- xMgxTi5O12 as anode materials for lithium-ion battery [J]. Journal of Alloys & Compounds, 2017, 722: 229–234.
    [2]
    SUN W, KUANG X, LIANG H, et al. Mechanical properties of tantalum carbide from high-pressure/high-temperature synthesis and first-principles calculations [J]. Physical Chemistry Chemical Physics, 2020, 22(9): 5018–5023. doi: 10.1039/C9CP06819H
    [3]
    CASTLE E, CSANÁDI T, GRASSO S, et al. Processing and properties of high-entropy ultra-high temperature carbides [J]. Scientific Reports, 2018, 8: 8609. doi: 10.1038/s41598-018-26827-1
    [4]
    ZHAO E, MENG J, MA Y, et al. Phase stability and mechanical properties of tungsten borides from first principles calculations [J]. Physical Chemistry Chemical Physics, 2010, 12(40): 13158–13165. doi: 10.1039/c004122j
    [5]
    ZHANG C, GUPTA A, SEAL S, et al. Solid solution synthesis of tantalum carbide-hafnium carbide by spark plasma sintering [J]. Journal of the American Ceramic Society, 2017, 100(5): 1853–1862. doi: 10.1111/jace.14778
    [6]
    KIM H, YOON J, DOH J, et al. Rapid sintering process and mechanical properties of binderless ultra fine tungsten carbide [J]. Materials Science and Engineering: A, 2006, 435: 717–724.
    [7]
    CHEN H H, BI Y, CHENG Y, et al. Elastic stability and electronic structure of tantalum boride investigated via first-principles density functional calculations [J]. Journal of Physics and Chemistry of Solids, 2012, 73(10): 1197–1202. doi: 10.1016/j.jpcs.2012.05.007
    [8]
    GLECHNER T, MAYRHOFER P H, HOLEC D, et al. Tuning structure and mechanical properties of Ta-C coatings by N-alloying and vacancy population [J]. Scientific Reports, 2018, 8: 17669. doi: 10.1038/s41598-018-35870-x
    [9]
    ZHANG Z G, LIANG H, CHEN H, et al. Exploring physical properties of tantalum carbide at high pressure and temperature [J]. Inorganic Chemistry, 2020, 59(3): 1848–1852. doi: 10.1021/acs.inorgchem.9b03055
    [10]
    LIN Z J, ZHANG J Z, LI B S, et al. Superhard diamond/tungsten carbide nanocomposites [J]. Applied Physics Letters, 2011, 98(12): 121914. doi: 10.1063/1.3570645
    [11]
    CEDILLOS-BARRAZA O, GRASSO S, AL NASIRI N, et al. Sintering behaviour, solid solution formation and characterisation of TaC, HfC and TaC–HfC fabricated by spark plasma sintering [J]. Journal of the European Ceramic Society, 2016, 36(7): 1539–1548. doi: 10.1016/j.jeurceramsoc.2016.02.009
    [12]
    ZHANG X, HILMAS G E, FAHRENHOLTZ W G. Densification and mechanical properties of TaC-based ceramics [J]. Materials Science and Engineering: A, 2009, 501(1/2): 37–43. doi: 10.1016/j.msea.2008.09.024
    [13]
    CHEN C, HE D, KOU Z, et al. B6O-based composite to rival polycrystalline cubic boron nitride [J]. Advanced Materials, 2007, 19(23): 4288–4291. doi: 10.1002/adma.200700836
    [14]
    LIANG H, PENG F, CHEN C, et al. High-pressure sintering of bulk MoSi2: microstructural, physical properties and mechanical behavior [J]. Materials Science and Engineering: A, 2018, 711: 389–396. doi: 10.1016/j.msea.2017.11.016
    [15]
    CHEN H, LIANG H, LIU L, et al. Hardness measurements for high-pressure prepared TaB and nano-TaC ceramics [J]. Results in Physics, 2017, 7: 3859–3862. doi: 10.1016/j.rinp.2017.10.006
    [16]
    KIM B R, WOO K D, DOH J M, et al. Mechanical properties and rapid consolidation of binderless nanostructured tantalum carbide [J]. Ceramics International, 2009, 35(8): 3395–3400. doi: 10.1016/j.ceramint.2009.06.012
    [17]
    ZHANG X, HILMAS G E, FAHRENHOLTZ W G, et al. Hot pressing of tantalum carbide with and without sintering additives [J]. Journal of the American Ceramic Society, 2007, 90(2): 393–401. doi: 10.1111/j.1551-2916.2006.01416.x
    [18]
    CEDILLOS-BARRAZA O, MANARA D, BOBORIDIS K, et al. Investigating the highest melting temperature materials: a laser melting study of the TaC-HfC system [J]. Scientific Reports, 2016, 6(1): 1–11. doi: 10.1038/s41598-016-0001-8
    [19]
    ANSTIS G R, CHANTIKUL P, LAWN B R, et al. A critical evaluation of indentation techniques for measuring fracture toughness: Ⅰ, direct crack measurements [J]. Journal of the American Ceramic Society, 1981, 64(9): 533–538. doi: 10.1111/j.1151-2916.1981.tb10320.x
    [20]
    KIM B R, WOO K D, YOON J K, et al. Mechanical properties and rapid consolidation of binderless niobium carbide [J]. Journal of Alloys and Compounds, 2009, 481(1/2): 573–576.
    [21]
    SCITI D, GUICCIARDI S, NYGREN M. Densification and mechanical behavior of HfC and HfB2 fabricated by spark plasma sintering [J]. Journal of the American Ceramic Society, 2008, 91(5): 1433–1440. doi: 10.1111/j.1551-2916.2007.02248.x
    [22]
    KRZANOWSKI J E, LEUCHTNER R E. Chemical, mechanical, and tribological properties of pulsed-laser-deposited titanium carbide and vanadium carbide [J]. Journal of the American Ceramic Society, 1997, 80(5): 1277–1280.
    • Relative Articles
    • Supplements(0)
    • Cited By
  • 加载中

Catalog

    通讯作者: 陈斌, bchen63@163.com
    • 1. 

      沈阳化工大学材料科学与工程学院 沈阳 110142

    1. 本站搜索
    2. 百度学术搜索
    3. 万方数据库搜索
    4. CNKI搜索

    Figures(5)  / Tables(1)

    Get Citation
    PDF
    XML

    Article Metrics

    Article views(4859) PDF downloads(43) Cited by()
    Proportional views
    Related

    Copyright©《高压物理学报》编辑部

    Tel:0816-2490042 E-mail:gaoya@caep.cn

    Shu ICP, 11011126 -2

    Supported by: Beijing Renhe Information Technology Co. Ltd support: info@rhhz.net  

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return