knowledge of professional and technical personnel Notice on the organization of advanced research class on high-pressure science and new materials of engineering
Volume 34 Issue 1
Jan 2020
Turn off MathJax
Article Contents
Chinese Journal of High Pressure Physics  > 2020  >  34(1): 015301.
XUE Pengcheng, FAN Wenjie, WANG Genwei, WANG Bin. Effects of Loading Angle and Linear Notch on Tensile Properties of Lithium-Ion Battery Separator[J]. Chinese Journal of High Pressure Physics, 2020, 34(1): 015301. doi: 10.11858/gywlxb.20190765
Citation: XUE Pengcheng, FAN Wenjie, WANG Genwei, WANG Bin. Effects of Loading Angle and Linear Notch on Tensile Properties of Lithium-Ion Battery Separator[J]. Chinese Journal of High Pressure Physics, 2020, 34(1): 015301. doi: 10.11858/gywlxb.20190765
shu

Effects of Loading Angle and Linear Notch on Tensile Properties of Lithium-Ion Battery Separator

doi: 10.11858/gywlxb.20190765
  • 1.

    Institute of Applied Mechanics, Taiyuan University of Technology, Taiyuan 030024, Shanxi, China

  • 2.

    Shanxi Key Laboratory of Material Strength & Structural Impact, College of Mechanical and Vehicle Engineering of Taiyuan University of Technology, Taiyuan 030024, Shanxi, China

  • 3.

    College of Engineering, Design and Physical Sciences, Brunel University, London UB83PH, UK

  • Received Date: 25 Apr 2019
  • Rev Recd Date: 08 May 2019
    Abstract
  • Lithium-ion battery separators act as the physical barriers to prevent contact between the positive and negative electrodes, and their structural integrity is critical to battery safety. In this paper, uniaxial tensile tests were carried out on four kinds of commercial separators, and the effects of loading angle and linear notch on tensile strength, elastic modulus and fracture mode were analyzed. The results show that the tensile strength of the 0° specimens without notch is the largest and the tensile strength of 90° specimens is the smallest. When the loading angles of two notched specimens are supplementary, their tensile strength is close to each other. For the notched specimens, the failure load is the largest when the notched direction is along 90°. The linear notched specimens have higher elastic modulus, but the plastic deformation is greatly reduced. Both the unnotched specimens and the notched specimens are broken along MD (machine direction) except for the 0° specimens along TD (transverse direction).

     

    • FullText(HTML)
  • loading
    • References(26)
  • [1]
    AVDEEV I, MARTINSEN M, FRANCIS A. Rate- and temperature-dependent material behavior of a multilayer polymer battery separator [J]. Journal of Materials Engineering and Performance, 2014, 23(1): 315–325. doi: 10.1007/s11665-013-0743-4
    [2]
    HUANG X S. Separator technologies for lithium-ion batteries [J]. Journal of Solid State Electrochemistry, 2011, 15(4): 649–662. doi: 10.1007/s10008-010-1264-9
    [3]
    ROTH E P, DOUGHTY D H, PILE D L. Effects of separator breakdown on abuse response of 18650 Li-ion cells [J]. Journal of Power Sources, 2007, 174(2): 579–583. doi: 10.1016/j.jpowsour.2007.06.163
    [4]
    SANTHANAGOPALAN S, RAMADASS P, ZHANG J Z. Analysis of internal short-circuit in a lithium ion cell [J]. Journal of Power Sources, 2009, 194(1): 550–557. doi: 10.1016/j.jpowsour.2009.05.002
    [5]
    DARCY E. Screening Li-ion batteries for internal shorts [J]. Journal of Power Sources, 2007, 174(2): 575–578. doi: 10.1016/j.jpowsour.2007.06.245
    [6]
    SPOTNITZ R M, WEAVER J, YEDUVAKA G, et al. Simulation of abuse tolerance of lithium-ion battery packs [J]. Journal of Power Sources, 2007, 163(2): 1080–1086. doi: 10.1016/j.jpowsour.2006.10.013
    [7]
    BÖHNSTEDT W. Challenges for automotive battery separator development [J]. Journal of Power Sources, 1997, 67(1/2): 299–305.
    [8]
    WANG X H, SHEN W H, HUANG X F, et al. Estimating the thickness of diffusive solid electrolyte interface [J]. Science China, 2017, 60(6): 064612.
    [9]
    MA Z S, XIE Z C, WANG Y, et al. Failure modes of hollow core-shell structural active materials during the lithiation-delithiation process [J]. Journal of Power Sources, 2015, 290: 114–122. doi: 10.1016/j.jpowsour.2015.05.008
    [10]
    WU H, XIE Z C, WANG Y, et al. Modeling diffusion-induced stress on two-phase lithiation in lithium-ion batteries [J]. European Journal of Mechanics A, 2018, 71: 320–325. doi: 10.1016/j.euromechsol.2018.04.005
    [11]
    HU B, MA Z S, LEI W X, et al. A chemo-mechanical model coupled with thermal effect on the hollow core-shell electrodes in lithium-ion batteries [J]. Theoretical and Applied Mechanics Letters, 2017, 7(4): 199–206. doi: 10.1016/j.taml.2017.09.001
    [12]
    WU H, XIE Z C, WANG Y, et al. A constitutive model coupling irradiation with two-phase lithiation for lithium-ion battery electrodes [J]. Philosophical Magazine, 2019, 99(8): 992–1013. doi: 10.1080/14786435.2019.1569767
    [13]
    ZHANG X W, SAHRAEI E, WANG K. Deformation and failure characteristics of four types of lithium-ion battery separators [J]. Journal of Power Sources, 2016, 327: 693–701. doi: 10.1016/j.jpowsour.2016.07.078
    [14]
    HALALAY I C, LUKITSCH M J, BALOGH M P, et al. Nanoindentation testing of separators for lithium-ion batteries [J]. Journal of Power Sources, 2013, 238: 469–477. doi: 10.1016/j.jpowsour.2013.04.036
    [15]
    WANG E, WU H P, CHIU C H, et al. The effect of battery separator properties on thermal ramp, overcharge and short circuiting of rechargeable Li-ion batteries [J]. Journal of the Electrochemical Society, 2019, 166(2): A125–A131. doi: 10.1149/2.0381902jes
    [16]
    XU J, WANG L B, GUAN J, et al. Coupled effect of strain rate and solvent on dynamic mechanical behaviors of separators in lithium ion batteries [J]. Materials & Design, 2016, 95: 319–328.
    [17]
    KALNAUS S, WANG Y L, TURNER J A. Mechanical behavior and failure mechanisms of Li-ion battery separators [J]. Journal of Power Sources, 2017, 348: 255–263. doi: 10.1016/j.jpowsour.2017.03.003
    [18]
    CHEN J H, HU H J, LI S, et al. Evolution of mechanical properties of polypropylene separator in liquid electrolytes for lithium-ion batteries [J]. Journal of Applied Polymer Science, 2018, 135(27): 46441. doi: 10.1002/app.46441
    [19]
    CANNARELLA J, LIU X Y, LENG C Z, et al. Mechanical properties of a battery separator under compression and tension [J]. Journal of the Electrochemical Society, 2014, 161(11): F3117–F3122. doi: 10.1149/2.0191411jes
    [20]
    XU H Y, ZHU M, MARCICKI J, et al. Mechanical modeling of battery separator based on microstructure image analysis and stochastic characterization [J]. Journal of Power Sources, 2017, 345: 137–145. doi: 10.1016/j.jpowsour.2017.02.002
    [21]
    WANG L B, YIN S, XU J. A detailed computational model for cylindrical lithium-ion batteries under mechanical loading: from cell deformation to short-circuit onset [J]. Journal of Power Sources, 2019, 413: 284–292. doi: 10.1016/j.jpowsour.2018.12.059
    [22]
    CHEN J C, YAN Y D, SUN T, et al. Deformation and fracture behaviors of microporous polymer separators for lithium ion batteries [J]. RSC Advances, 2014, 4(29): 14904. doi: 10.1039/c4ra00983e
    [23]
    DROZDOV A D, DE C CHRISTIANSEN J. Viscoelasticity and viscoplasticity of semicrystalline polymers: structure-property relations for high-density polyethylene [J]. Computational Materials Science, 2007, 39(4): 729–751. doi: 10.1016/j.commatsci.2006.09.001
    [24]
    LI X X, WU H Y, WANG Y, et al. Study on the β to α transformation of PP/POE blends with β-phase nucleating agent during the tensile deformation process [J]. Materials Science and Engineering A, 2010, 527(3): 531–538. doi: 10.1016/j.msea.2009.08.007
    [25]
    ROZANSKI A, GALESKI A, DEBOWSKA M. Initiation of cavitation of polypropylene during tensile drawing [J]. Macromolecules, 2011, 44(1): 20–28. doi: 10.1021/ma1018523
    [26]
    ZUO F, KEUM J K, CHEN X M, et al. The role of interlamellar chain entanglement in deformation-induced structure changes during uniaxial stretching of isotactic polypropylene [J]. Polymer, 2007, 48(23): 6867–6880. doi: 10.1016/j.polymer.2007.08.065
    • Relative Articles
    • Supplements(0)
    • Cited By
  • 加载中

Catalog

    通讯作者: 陈斌, bchen63@163.com
    • 1. 

      沈阳化工大学材料科学与工程学院 沈阳 110142

    1. 本站搜索
    2. 百度学术搜索
    3. 万方数据库搜索
    4. CNKI搜索

    Figures(6)  / Tables(1)

    Get Citation
    PDF
    XML

    Article Metrics

    Article views(8136) PDF downloads(35) Cited by()
    Proportional views
    Related

    Copyright©《高压物理学报》编辑部

    Tel:0816-2490042 E-mail:gaoya@caep.cn

    Shu ICP, 11011126 -2

    Supported by: Beijing Renhe Information Technology Co. Ltd support: info@rhhz.net  

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return