预应力对陶瓷抗侵彻性能影响规律的数值模拟

吴雪; 张先锋; 丁力; 谈梦婷; 包阔; 陈贝贝

doi:10.11858/gywlxb.20170610

预应力对陶瓷抗侵彻性能影响规律的数值模拟

doi: 10.11858/gywlxb.20170610

南京理工大学机械工程学院, 江苏南京 210094

基金项目:

国家自然科学基金 11772159

中组部青年拔尖人才支持计划 2014

中央高校基本科研业务专项基金 30917011104

中央高校基本科研业务专项基金 30916011305

详细信息

作者简介:
吴雪(1991-), 女, 硕士研究生, 主要从事冲击动力学研究.E-mail:wuxue0911@163.com

通讯作者:
张先锋(1978-), 男, 博士, 教授, 主要从事高效毁伤与防护研究

中图分类号: O385
计量
- 文章访问数: 7237
- HTML全文浏览量: 3063
- PDF下载量: 226
出版历程
- 收稿日期: 2017-07-06
- 修回日期: 2017-07-20

Numerical Simulation of the Effect of Pre-stress on the Ballistic Performance of Ceramics

School of Mechanical Engineering, Nanjing University of Science & Technology, Nanjing 210094, China

摘要

摘要: 为研究预应力陶瓷的抗侵彻性能，利用AUTODYN仿真软件模拟了对SiC陶瓷施加预应力的过程，并开展了长杆弹以不同速度侵彻预应力陶瓷的数值仿真研究，确定了预应力陶瓷的抗侵彻性能。通过对比分析，得到了不同载荷下陶瓷内部的应力分布状态，以及陶瓷抗侵彻性能与预应力的关系。结果表明：对陶瓷施加预应力可以有效提高其抗侵彻能力；但随着加载预应力的进一步提高，即当陶瓷中心部位预应力大于112MPa时，陶瓷的抗侵彻能力反而下降，陶瓷加载的预应力与其抗侵彻性能之间存在最佳匹配关系。
- 陶瓷装甲 /
- 预应力陶瓷 /
- 抗侵彻性能
Abstract: In this work we studied the processes of applying pre-stress on SiC ceramics by using the finite element software AUTODYN.We established a model of long-rod projectile of different velocities penetrating ceramics with different pre-stress values to investigate the ballistic performance of the pre-stress ceramic, and obtained the stress distributions in the ceramic under different loading conditions through the comparison and analysis of the results, as well as the relation of different pre-stress and ballistic performance of the ceramic.The simulated results show that the appropriate pre-stress can improve the ballistic performance of ceramic, but the ballistic performance of ceramic is reduced when the pre-stress value is greater than 112 MPa, and that there exists a best matching relationship between the pre-stress value and the ballistic performance of the ceramics.
- ceramic armor /
- pre-stress ceramic /
- ballistic performance

HTML全文

图 1 陶瓷预应力加载模型

Figure 1. Applying pre-stress on ceramic

下载: 全尺寸图片幻灯片

图 2 长杆弹侵彻预应力陶瓷模型

Figure 2. Long-rod projectile penetrating ceramic

下载: 全尺寸图片幻灯片

图 3 陶瓷预应力加载过程

Figure 3. Pre-stress loading process of ceramic

下载: 全尺寸图片幻灯片

图 4 预应力加载过程中陶瓷内部应力云图

Figure 4. Stress in ceramic during pre-stress process

下载: 全尺寸图片幻灯片

图 5 陶瓷中心点应力-时间曲线

Figure 5. Stress-time curves of ceramic at the center point

下载: 全尺寸图片幻灯片

图 6 高斯点分布

Figure 6. Positions of Gaussian points

下载: 全尺寸图片幻灯片

图 7 陶瓷内部不同高斯点处应力分布

Figure 7. Stress curves at different Gaussian points inside the ceramic

下载: 全尺寸图片幻灯片

图 8 数值模拟与实验^[20]所得DOP对比

Figure 8. Comparison of DOP between simulation and experimental results^[20]

下载: 全尺寸图片幻灯片

图 9 侵彻过程中陶瓷内部应力分布云图

Figure 9. Stress cloud in ceramic during penetration process

下载: 全尺寸图片幻灯片

图 10 长杆弹头位移随时间变化曲线

Figure 10. Displacement variations of log-rod projectile over time

下载: 全尺寸图片幻灯片

图 11 DOP随速度、压缩比的变化

Figure 11. DOP vs. impact velocity and compression ratio

下载: 全尺寸图片幻灯片

参考文献(20)

[1]	刘桂武, 倪长也, 金峰, 等.陶瓷/金属复合装甲抗弹约束效应述评[J].西安交通大学学报, 2011, 45(3):7-15, 24. doi: 10.7652/xjtuxb201103002 LIU G W, NI C Y, JIN F, et al.Review of anti-ballistic confinement effecs of ceramic-metal composite armor[J].Journal of Xi'an Jiaotong University, 2011, 45(3):7-15, 24. doi: 10.7652/xjtuxb201103002
[2]	高举贤, 吴玉炎, 白蓉裳, 等.陶瓷防弹性能的研究[J].弹箭与制导学报, 1986(2):7-17. http://mall.cnki.net/magazine/Article/ZGGT201006004.htm
[3]	王为民, 傅正义, 张金咏, 等. 陶瓷材料抗超高速弹丸的侵彻过程研究[C]//中国空间科学学会空间材料专业委员会2012学术交流会议论文(摘要)集, 2012.
[4]	LASALVIA J C, MCCAULEY J W.Inelastic deformation mechanisms and damage in structural ceramics subjected to high-velocity impact[J].International Journal of Applied Ceramic Technology, 2010, 7(5):595-605. doi: 10.1111/ijac.2010.7.issue-5
[5]	SHERMAN D.Impact failure mechanisms in alumina tiles on finite thickness support and the effect of confinement[J].International Journal of Impact Engineering, 2000, 24(3):313-328. doi: 10.1016/S0734-743X(99)00147-5
[6]	MEYER H W, KLEPONIS D S.Modeling the high strain rate behavior of titanium undergoing ballistic impact and penetration[J].International Journal of Impact Engineering, 2001, 26(1):509-521. https://www.deepdyve.com/lp/elsevier/modeling-the-high-strain-rate-behavior-of-titanium-undergoing-PFjFhl7cic
[7]	李平, 李大红, 宁建国, 等.Al₂O₃陶瓷复合靶抗长杆弹侵彻性能和机理实验研究[J].爆炸与冲击, 2003, 23(4):289-294. http://image.sciencenet.cn/olddata/kexue.com.cn/upload/blog/file/2010/8/2010828175240976253.xls LI P, LI D H, NING J G, et al.Experimental study on the ballistic performance and mechanism of confined ceramic targets against long rod penetrators[J].Explosion and Shock Waves, 2003, 23(4):289-294. http://image.sciencenet.cn/olddata/kexue.com.cn/upload/blog/file/2010/8/2010828175240976253.xls
[8]	井玉安, 果世驹, 韩静涛.钢/Al₂O₃陶瓷/钢轻型复合装甲板抗弹性能[J].北京科技大学学报, 2007, 29(4):402-407. http://subject.wanfangdata.com.cn/xstjbg/2010/gyjs4.html JING Y A, GUO S J, HAN J T.Ballistic property of steel/ceramic/steel composite armor[J].Journal of University of Science and Technology Beijing, 2007, 29(4):402-407. http://subject.wanfangdata.com.cn/xstjbg/2010/gyjs4.html
[9]	CHI R, SERJOUEI A, SRIDHAR I, et al.Pre-stress effect on confined ceramic armor ballistic performance[J].International Journal of Impact Engineering, 2015, 84:159-170. doi: 10.1016/j.ijimpeng.2015.05.011
[10]	HOLMQUIST T J, JOHNSON G R.Response of silicon carbide to high velocity impact[J].Journal of Applied Physics, 2002, 91(9):5858-5866. doi: 10.1063/1.1468903
[11]	谈梦婷, 张先锋, 何勇, 等.长杆弹撞击装甲陶瓷的界面击溃效应数值模拟[J].兵工学报, 2016, 37(4):627-634. http://www.cnki.com.cn/Article/CJFDTotal-JSJZ201502002.htm TAN M T, ZHANG X F, HE Y, et al.Numerical simulation on interface defeat of ceramic armor impacted by long-rod projectile[J].Acta Armamentarii, 2016, 37(4):627-634. http://www.cnki.com.cn/Article/CJFDTotal-JSJZ201502002.htm
[12]	ZHU D, YAN S, LI B.Single-grit modeling and simulation of crack initiation and propagation in SiC grinding using maximum undeformed chip thickness[J].Computational Materials Science, 2014, 92:13-21. doi: 10.1016/j.commatsci.2014.05.019
[13]	HOLMQUIST T J, JOHNSON G R.Characterization and evaluation of silicon carbide for high-velocity impact[J].Journal of Applied Physics, 2005, 97(9):093502. doi: 10.1063/1.1881798
[14]	CRONIN D S, BUI K, KAUFMANN C, et al. Implementation and validation of the Johnson-Holmquist ceramic material model in LS-DYNA[C]//Proceedings of 4th European LS-DYNA Users Conference. Ontario, Canada: University of Waterloo, 2003, 1: 47-60.
[15]	JOHNSON G R, COOK W H. A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures[C]//Proceedings of the 7th International Symposium on Ballistics, 1983, 21: 541-547.
[16]	LUNDBERG P, RENSTRÖM R, LUNDBERG B.Impact of conical tungsten projectiles on flat silicon carbide targets:transition from interface defeat to penetration[J].International Journal of Impact Engineering, 2006, 32(11):1842-1856. doi: 10.1016/j.ijimpeng.2005.04.004
[17]	LEE J K. Analysis of multi-layered materials under high velocity impact using CTH[D]. Air Force Institute of Technology Wright-Patterson AFB OH, Graduate School of Engineering and Management, 2008. https://aps.ieee.org/news/53-education/323-past-distinguished-lecturer-appointments
[18]	JOHNSON G R, COOK W H.Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures[J].Engineering Fracture Mechanics, 1985, 21(1):31-48. doi: 10.1016/0013-7944(85)90052-9
[19]	HOLMQUIST T J, JOHNSON G R.Modeling prestressed ceramic and its effect on ballistic performance[J].International Journal of Impact Engineering, 2005, 31(2):113-127. doi: 10.1016/j.ijimpeng.2003.11.002
[20]	SERJOUEI A, GOUR G, ZHANG X, et al.On improving ballistic limit of bi-layer ceramic/metal armor[J].International Journal of Impact Engineering, 2017, 105:54-67. doi: 10.1016/j.ijimpeng.2016.09.015